Hall Sensor SKU: PZSHED0001 - Revision history

Chenqi: /* Case and Test Code */

2022-01-13T06:34:23Z

‎Case and Test Code

2022-01-13T06:32:25Z

‎Case and Test Code

2022-01-13T06:31:20Z

‎Case and Test Code

2022-01-12T14:22:26Z

‎Case and Test Code

2022-01-12T14:20:58Z

‎Case and Test Code

2022-01-12T13:39:46Z

‎Case and Test Code

2022-01-12T13:36:01Z

‎Case and Test Code

2022-01-12T13:35:23Z

‎Case and Test Code

2022-01-12T13:17:48Z

‎DataSheet

2022-01-12T13:17:01Z

‎DataSheet

@@ Line 54: / Line 54: @@
 |[[File:PZSHED0001-4.jpg |left|600px]]
 |}
-'''Raspberry Pi test method'''
+'''Raspberry Pi Test Method'''
 *Connect the sensor to the Raspberry Pi 4B, and put the test code on the Raspberry Pi system in the form of a folder.
 *If pip is not installed, you must install pip first: (skip this step if installed)

@@ Line 59: / Line 59: @@
 *Enter the code file on the left side of the Raspberry Pi, right-click and select Open with...
 {|-
-|[[File:PZSHED0001-8.png |left|600px]]
+|[[File:PZSHED0001-8.jpg |left|600px]]
 |}
 Choose '''Geany''' Software
 {|-
-|[[File:PZSHED0001-9.png |left|600px]]
+|[[File:PZSHED0001-9.jpg |left|600px]]
-|[[File:PZSHED0001-10.png |left|600px]]
+|[[File:PZSHED0001-10.jpg |left|600px]]
 |}
 '''Raspberry Pi Code'''

@@ Line 59: / Line 59: @@
 *Enter the code file on the left side of the Raspberry Pi, right-click and select Open with...
 {|-
-|[[File:PZSHED0001-5.png |left|600px]]
+|[[File:PZSHED0001-8.png |left|600px]]
 |}
 Choose '''Geany''' Software
 {|-
-|[[File:PZSHED0001-6.png |left|600px]]
+|[[File:PZSHED0001-9.png |left|600px]]
-|[[File:PZSHED0001-7.png |left|600px]]
+|[[File:PZSHED0001-10.png |left|600px]]
 |}
 '''Raspberry Pi Code'''

@@ Line 26: / Line 26: @@
 |}
 '''Arduino Code'''
+<pre>
 [[Media: Hall Magnetic Sensor - Arduino Code Download.rar]]
@@ Line 52: / Line 68: @@
 '''Raspberry Pi Code'''
 <pre>
-int ledPin = 13;                // choose the pin for the LED
+import RPi.GPIO as GPIO
-int inputPin = 2;               // Connect Hall sensor to Pin2
+from time import sleep
-int val = 0;                    // variable for reading the pin status
+val=0
-void setup() {
-  pinMode(ledPin, OUTPUT);      // declare LED as output
+sensorPin = 18
-  pinMode(inputPin, INPUT);     // declare pushbutton as input
-−
-void loop(){
+GPIO.setmode(GPIO.BCM)
-  val = digitalRead(inputPin);  // read input value
-  if (val == HIGH) {            // check if the input is HIGH
+GPIO.setup(sensorPin,GPIO.IN)
-    digitalWrite(ledPin, LOW);  // turn LED OFF
-  } else {
+while True:
-     digitalWrite(ledPin, HIGH); // turn LED ON
+     val = GPIO.input(sensorPin)
+    print(val);
+    if(val == 0):
 </pre>
 [[Media: Hall Magnetic Sensor - Raspberry Pi Code Download.rar]]

@@ Line 51: / Line 51: @@
 |}
 '''Raspberry Pi Code'''
+<pre>
 [[Media: Hall Magnetic Sensor - Raspberry Pi Code Download.rar]]
 ----

← Older revision		Revision as of 13:35, 12 January 2022
Line 26:		Line 26:
	\|}		\|}
	'''Arduino Code'''		'''Arduino Code'''
		+	[[Media:Hall Magnetic Sensor - Arduino Code Download.rar]]

@@ Line 17: / Line 17: @@
 ----
 =='''DataSheet '''==
-[[Media: OH9249.rar]]
+[[Media: OH9249.pdf]]
 ----