Difference between revisions of "Metal DC Geared Motor w/Encoder CQGB37Y001"
| Line 32: | Line 32: | ||
==10:1== | ==10:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 10:1 | *Gear Ratio: 10:1 | ||
*Reducer L Length: 19mm | *Reducer L Length: 19mm | ||
| Line 47: | Line 48: | ||
==18.8:1== | ==18.8:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 18.8:1 | *Gear Ratio: 18.8:1 | ||
*Reducer L Length: 22mm | *Reducer L Length: 22mm | ||
| Line 62: | Line 64: | ||
==30:1== | ==30:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 30:1 | *Gear Ratio: 30:1 | ||
*Reducer L Length: 22mm | *Reducer L Length: 22mm | ||
| Line 77: | Line 80: | ||
==43.8:1== | ==43.8:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 43.8:1 | *Gear Ratio: 43.8:1 | ||
*Reducer L Length: 24mm | *Reducer L Length: 24mm | ||
| Line 92: | Line 96: | ||
==56.3:1== | ==56.3:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 56.3:1 | *Gear Ratio: 56.3:1 | ||
*Reducer L Length: 24mm | *Reducer L Length: 24mm | ||
| Line 107: | Line 112: | ||
==70:1== | ==70:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 70:1 | *Gear Ratio: 70:1 | ||
*Reducer L Length: 24mm | *Reducer L Length: 24mm | ||
| Line 122: | Line 128: | ||
==90:1== | ==90:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 90:1 | *Gear Ratio: 90:1 | ||
*Reducer L Length: 24mm | *Reducer L Length: 24mm | ||
| Line 137: | Line 144: | ||
==131:1== | ==131:1== | ||
| + | SPECIFICATION-6V | ||
*Gear Ratio: 131:1 | *Gear Ratio: 131:1 | ||
*Reducer L Length: 26.5mm | *Reducer L Length: 26.5mm | ||
Revision as of 08:46, 2 April 2018
Contents
Description
- This is metal DC geared motor w/Encoder, Operating voltage is 6V-12V. for Projects Such as Robot, Custom Servo, Arduino and 3D Printers.
- The rear of the motor is equipped with a dual channel Holzer effect encoder, AB dual output, single circuit per cycle pulse 16CPR, double down the road, a total output of 64CPR.
- These units have a 0.61 inch long, 6 mm(0.24 inch)-diameter D-shaped output shaft. This motor is intended for use at 12V, though the motor can begin rotating at voltages as low as 1V.
- The face plate has six mounting holes evenly spaced around the outer edge threaded for M3 screws. These mounting holes form a regular hexagon and the centers of neighboring holes are 15.5 mm(0.61 inch) apart.
NOTE
Do not screw too far into the mounting holes as the screws can hit the gears. CQRobot Manufacturer recommends screwing no further than 3mm (1/8 inch) into the screw hole.
6.25:1
SPECIFICATION-6V
- Gear Ratio: 6.25:1
- Reducer L Length: 19mm
- No-load Speed: 880rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 1.5kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 6.25:1
- Reducer L Length: 19mm
- No-load Speed: 1760rpm
- No-load Current: 250mA
- Stall Torque: 3.1kg.cm
- Stall Current: 6.5A
10:1
SPECIFICATION-6V
- Gear Ratio: 10:1
- Reducer L Length: 19mm
- No-load Speed: 550rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 2.5kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 10:1
- Reducer L Length: 19mm
- No-load Speed: 1100rpm
- No-load Current: 250mA
- Stall Torque: 5.1kg.cm
- Stall Current: 6.5A
18.8:1
SPECIFICATION-6V
- Gear Ratio: 18.8:1
- Reducer L Length: 22mm
- No-load Speed: 292rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 4.3kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 18.8:1
- Reducer L Length: 22mm
- No-load Speed: 585rpm
- No-load Current: 250mA
- Stall Torque: 8.6kg.cm
- Stall Current: 6.5A
30:1
SPECIFICATION-6V
- Gear Ratio: 30:1
- Reducer L Length: 22mm
- No-load Speed: 183rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 6.8kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 30:1
- Reducer L Length: 22mm
- No-load Speed: 366rpm
- No-load Current: 250mA
- Stall Torque: 13kg.cm
- Stall Current: 6.5A
43.8:1
SPECIFICATION-6V
- Gear Ratio: 43.8:1
- Reducer L Length: 24mm
- No-load Speed: 125rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 8.9kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 43.8:1
- Reducer L Length: 24mm
- No-load Speed: 251rpm
- No-load Current: 250mA
- Stall Torque: 18kg.cm
- Stall Current: 6.5A
56.3:1
SPECIFICATION-6V
- Gear Ratio: 56.3:1
- Reducer L Length: 24mm
- No-load Speed: 97rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 11kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 56.3:1
- Reducer L Length: 24mm
- No-load Speed: 195rpm
- No-load Current: 250mA
- Stall Torque: 23kg.cm
- Stall Current: 6.5A
70:1
SPECIFICATION-6V
- Gear Ratio: 70:1
- Reducer L Length: 24mm
- No-load Speed: 78rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 14kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 70:1
- Reducer L Length: 24mm
- No-load Speed: 157rpm
- No-load Current: 250mA
- Stall Torque: 28kg.cm
- Stall Current: 6.5A
90:1
SPECIFICATION-6V
- Gear Ratio: 90:1
- Reducer L Length: 24mm
- No-load Speed: 61rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 18kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 90:1
- Reducer L Length: 24mm
- No-load Speed: 122rpm
- No-load Current: 250mA
- Stall Torque: 36kg.cm
- Stall Current: 6.5A
131:1
SPECIFICATION-6V
- Gear Ratio: 131:1
- Reducer L Length: 26.5mm
- No-load Speed: 41rpm (Plus/Minus 10%)
- No-load Current: 120mA
- Stall Torque: 22kg.cm
- Stall Current: 3.0A
SPECIFICATION-12V
- Gear Ratio: 131:1
- Reducer L Length: 26.5mm
- No-load Speed: 83rpm
- No-load Current: 250mA
- Stall Torque: 45kg.cm
- Stall Current: 6.5A
SPECIFICATION-Encoder
- Encoder Operating Voltage: 3.3V - 24V
- Encoder Type: Hall (Incremental Type)
- Encoder Resolution: 64CPR
Display
 |
 |
 |
 |
 |
 |
DISTRIBUTION LIST
- 1 * 6V/12V Metal DC Geared Motor w/Encoder
